AMX NetLinx NXB-KNX Especificações

Operation/Reference GuideControl System AccessoriesNXB-KNXNetLinx KNX InterfaceInitial Release: 5/15/2008

Configuration6NXB-KNX NetLinx KNX InterfaceAccessing the WebConsoleFrom any PC that has access to the LAN that the NXB-KNX resides on:1. Open a web br

Configuration7NXB-KNX NetLinx KNX InterfaceSecurity SettingsSelect Security Settings from the Admin drop-down menu to open the Security Settings page

Configuration8NXB-KNX NetLinx KNX Interface Click Accept to save your changes. Note that changes on this page take effect immediately.  Click Cancel

Configuration9NXB-KNX NetLinx KNX InterfacePort SettingsSelect Port Settings from the Admin drop-down menu to open the Port Settings page (FIG. 7). Us

Configuration10NXB-KNX NetLinx KNX InterfaceClock ManagerHover the cursor over the Clock Manager option in the Admin menu to open the Clock Manager su

Configuration11NXB-KNX NetLinx KNX Interface Click Accept to save your changes. Note that changes on this page take effect immediately.  Click Cance

Configuration12NXB-KNX NetLinx KNX Interface Click Accept to save your changes. Note that changes on this page take effect immediately.  Click Cance

Configuration13NXB-KNX NetLinx KNX InterfaceApplication UpgradeSelect Application Upgrade from the Admin drop-down menu to open the Application Upgrad

Configuration14NXB-KNX NetLinx KNX InterfaceFirmware UpgradeSelect Firmware Upgrade from the Admin drop-down menu to open the Firmware Upgrade Manager

Programming - Telnet Commands15NXB-KNX NetLinx KNX InterfaceProgramming - Telnet CommandsOverviewThe NXB-KNX supports Telnet communications. This type

AMX Limited Warranty and DisclaimerThis Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Part

Programming - Telnet Commands16NXB-KNX NetLinx KNX InterfaceTerminal CommandsThe Terminal commands listed in the following table can be sent directly

Programming - Telnet Commands17NXB-KNX NetLinx KNX InterfaceTerminal Commands (Cont.)Command DescriptionMEM Displays the largest free block of the NXB

Programming - Telnet Commands18NXB-KNX NetLinx KNX InterfaceTerminal Commands (Cont.)Command DescriptionSET DNS Sets up the DNS configuration.This com

Programming - Telnet Commands19NXB-KNX NetLinx KNX InterfaceTerminal Commands (Cont.)Command DescriptionSET HTTPS PORT Sets the NXB-KNX’s IP port list

Programming - Telnet Commands20NXB-KNX NetLinx KNX InterfaceTerminal Commands (Cont.)Command DescriptionSET TELNET PORT Sets the NXB-KNX’s IP port lis

Programming - Telnet Commands21NXB-KNX NetLinx KNX InterfaceTerminal Commands (Cont.)Command DescriptionSHOW HEAP Displays heap usage statistics.SHOW

Programming - Telnet Commands22NXB-KNX NetLinx KNX Interface

Programming - Telnet Commands23NXB-KNX NetLinx KNX Interface

5/08 ©2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without no

Table of ContentsiNXB-KNX NetLinx KNX InterfaceTable of ContentsOverview ...

iiNXB-KNX NetLinx KNX InterfaceTable of Contents

Overview1NXB-KNX NetLinx KNX InterfaceOverviewThe NetLinx NXB-KNX interface (FG2031-01) allows AMX NetLinx Integrated Controllers the ability to contr

Overview2NXB-KNX NetLinx KNX InterfaceNXB-KNX Specifications (Cont.)Operating Environment:• Operating Temperature: 32°F - 104°F (0°C - 40°C)• Relative

Installation3NXB-KNX NetLinx KNX InterfaceInstallationWiring and ConnectionsThe NXB-KNX is installed between the NetLinx Master and the KNX control bu

Installation4NXB-KNX NetLinx KNX InterfacePoE (Power Over Ethernet)The NXB-KNX uses CAT5/CAT6 wire via the Ethernet port for PoE power. Use the PS-POE

Configuration5NXB-KNX NetLinx KNX InterfaceConfigurationOverviewNXB-KNX units have a built-in WebConsole that allows you to make various configuration