AMX MAX-CSD 10 Manual do Utilizador descarregar pdf (Página 4)

the CSD network and the project file network address. 6946

67. Duplicate PowerMatch Input & Output block labels are now changed to '----' on save and re-open. 5473

68. ESP-88 Fatal error (red power LED) no longer occurs if a design is uploaded without input cards installed in

the ESP. 5738

69. Changing multiple CC64 IPs to match device in Project View no longer causes temporary duplicate IP

addresses in Network Setup 6928

70. ControlSpace Designer only warns of different project network address once instead of for each device in

a project when opening a design file with a different project network address than current settings. 6938

71. CC-16 assignment is now cleared correctly when blanked via a parameter set. 7015

72. ControlSpace Designer now handles '-?' when opening a design with -inf value from Russian Windows

Operating System 4850

KNOWN ISSUES

1. The remaining incompatibility resulting from changes to the file-compression options available

under Windows is between Windows 7 64-bit PCs and older installations/designs uploaded using

XP. For these situations the ‘Save Retrieved Design to File’ option on the ‘System’ menu can be

used to retrieve the compressed .cab to the desktop. From there the file can then be extracted

and once the file extension has been changed from .xml to .csp the file can be opened in

ControlSpace Designer as normal. To change the extension you’ll need to ensure that ‘Hide

extensions for known file types’ is unchecked in the Windows folder options.

2. Firmware update may fail when using Win 7 64-bit OS with certain PC and network switch

combinations, connecting directly using a crossover cable is a workaround. (#6344)

3. We have also seen firmware update failures via Ethernet if the PC network adaptor has the

‘Large Send Offload (IPv4) = enabled. Disabling this setting appears to resolve the issue (#6841))

4. Changing PM8500N Array EQ parameters via Parameter Set is not currently supported.

5. Currently Band Pass bypass parameters are not recalled correctly via Parameter Set without

ControlSpace Designer on-line. (#6035)

6. Whilst most signal processing groups that span multiple PM8500Ns are now maintained when

ControlSpace Designer is disconnected, Input PEQ, Array EQ and Band Pass modules are not.

(#6107)

7. It is possible that ControlSpace Designer can become out-of-sync or lose communication with the

hardware if Parameter Sets are recalled in quick succession. Hardware functions correctly when

ControlSpace Designer is disconnected. (#6426/6912)

8. Loading a locked loudspeaker preset to a SpeakerPEQ module stored in a Parameter Set or

Group whilst online can cause undesirable side-effects. In this situation it is best to go offline,

make the change and re-send the design to the hardware. (#6366)

9. The volume levels displayed on CC-64s can get out-of-sync if the same PM8500N output is

assigned to multiple CC-64s. This issue does not occur when using an ESP. (# 6312)

10. It is possible in larger systems that changing the CC-64 control assignments dynamically may

result in the LED ladders being un-lit and the level jumping to -60db when the encoder is rotated

one-click left. This no longer occurs in smaller systems. (#6106)

11. In systems with multiple ESPs, dynamically re-assigning a CC-64 or CC-16 control from a Group

to an individual module, such as a selector or a gain can result in unexpected behavior. The CC-

64 or CC-16 may continue to display updates to the Group value even after the control has been

changed. The issue does not occur when changing the assignment from one Group to another, or

an individual module to another. (#6442/5165)

12. When changing CC-16/64 assignments via Parameter Set the stored ‘Off at Minimum’ property is

currently ignored by the hardware, but the change is made correctly in ControlSpace Designer.

(#6852)

13. An issue can occur with grouped selectors in multiple ESP systems, whereby the CC-16 can

appear locked or frozen. A workaround is to assign one of the group members to the CC-16

instead. (#6611)

1 2 3 4 5 6 7 8 9 ... 21 22

Comentários a estes Manuais

Sem comentários

AMX MAX-CSD 10 Manual do Utilizador Página 4

Comentários a estes Manuais