Amx Multimode Dimmer Module RDM-MDM Manual do Utilizador descarregar pdf

Installation Sheet

RDM-MDM Multimode Dimmer Module

2400 W

The RDM-MDM Multimode Dimmer Module is ideally used in situations

where the load is not specified or the load may change at the last moment.

This unit is a unique combination 2400 W Incandescent dimmer,

2400 W Switch, or 2400 W FDB fluorescent dimmer. It consists of a heavy

duty SSR construction for dimming and a heavy duty positive air gap relay

for switching. The RDM-MDM module's 120 and 240-277 VAC ratings are

CE, UL, and C-UL approved.

RDM-MDM UL and C-UL Ratings:

• 120 VAC, 50/60 Hz, 2400 W per circuit

• 240/277 VAC, 50/60 Hz, 2400 W per circuit

Specifications:

• Dimensions (HW): 10.00" x 2.75" (25.40 cm x 6.99 cm)

• Phase dependant dimming

• Use wires rated at 75°C (167°F)

• Torque terminals to 7 in-lbs (0.8 N/M)

• Max. wire size: 10 AWG (4 mm²)

• Wire stripping length: 0.28" (7 mm)

• Weight: 4.5 lbs (2.04 kg)

• BTU/hr: 300

• Control current: 190 mA @ 12 VDC

Suggested Loads:

Caution Pre-Installation Notes:

• All Class 1 wiring must be connected to proper terminals.

• All control wiring must be connected to proper terminals.

• Disconnect power while installing or connecting the unit.

• Keep top and bottom air vents clear at all times.

• Test loads for shorts before connecting.

• Use low-voltage wires with a 300 volt rating or greater.

• Use field-installed copper conductors.

• Run all low-voltage and control wires away from heat producing parts

of the dimmer.

• Each dimming circuit must have a separate neutral connection.

• All electrical ratings are for continuous duty.

• For indoor use only.

• AC lighting loads only.

• This module may require extra power from the AXlink connection or an

external power supply connected to the control card.

Connecting RDM Series Modules to the RDM-MDM:

FIG. 1 RDM-MDM

• Incandescent • Two-wire, phase-controlled ballast

• Low-voltage • Three-wire, phase-controlled ballast

• Neon, cold-cathode • Switched fluorescent ballast

Line

Neutral

Dimmed

Switched

350 µS Choke

Mechanical Relay

2400 W power device

Low-voltage control

wiring: four-pin connector

to AMX Lighting master

controller

Mounting points

High-voltage

connections

FIG. 2 Connecting RDM series modules to the RDM-MDM

Pin 4 (GND)

Pin 3 (RLY)

Pin 2 (DIM)

Pin 1 (+12 V)

RDM-MDM four-pin module connector

4-pin plug from a RDM series module

Note: The 4-pin plugs from the module

connector to the 4-pin connector on the

master (black plug cover facing up).

1 2

Installation Sheet 1

Resumo do Conteúdo

Página 1 - Installation Sheet

Installation SheetRDM-MDM Multimode Dimmer Module2400 WThe RDM-MDM Multimode Dimmer Module is ideally used in situations where the load is not specifi

Página 2

AMX Corporation reserves the right to alter specifications without notice at any time. For full warranty information, refer to the AMX Instruction Man

Comentários a estes Manuais

Sem comentários

Amx Multimode Dimmer Module RDM-MDM Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Amx Multimode Dimmer Module RDM-MDM. AMX Multimode Dimmer Module RDM-MDM User Manual [en] [de] [fr] Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Amx Multimode Dimmer Module RDM-MDM