AMX EXB-COM2 Especificações

Operation/Reference GuideCentral ControllersICSLan Device Control BoxesEXB-COM2EXB-I/O8EXB-IRS4EXB-MP1EXB-REL8Last Revised: 8/02/2012

ICSLan Device Control Boxes2 ICSLan Device Control BoxesCommon FeaturesMany features are common to all products in the EXB family, as described in th

ICSLan Device Control Boxes3 ICSLan Device Control Boxes LAN/PoE PortThe LAN/PoE (RJ45) port on all EXB Modules provides 10/100 BaseT network connect

ICSLan Device Control Boxes4 ICSLan Device Control BoxesDetailed LED BehaviorThe table below provides detailed descriptions of all blink patterns for

Installation5 ICSLan Device Control Boxes InstallationMounting Options (Rack Trays and Mounting Brackets)Refer to the documentation provided with eac

Installation6 ICSLan Device Control BoxesAVB-VSTYLE-POLE-MNT (FG1010-723)V Style Single Module Pole Mounting Kit - Suspend a single module to a pole

Installation7 ICSLan Device Control Boxes SAFETY INSTRUCTIONSFor UL compliance, the EXB family of ICSLan Device Control Boxes should be powered dir

Installation8 ICSLan Device Control Boxes

Network Configuration9 ICSLan Device Control Boxes Network ConfigurationOverviewEXB modules support two IP addressing modes: Static IP, and DHCP (wit

Network Configuration10 ICSLan Device Control BoxesTelnet IP Configuration CommandsThe SET IP (page 58) and GET IP (page 56) Telnet commands listed i

Network Configuration11 ICSLan Device Control Boxes Factory Default ParametersFactory Default Parameters are the values stored in the unit at the tim

AMX Limited Warranty and DisclaimerThis Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Part

Network Configuration12 ICSLan Device Control BoxesDevice IDs Using the ID PushbuttonUse the ID Pushbutton (on the front panel of all EXB Modules) to

Network Configuration13 ICSLan Device Control Boxes Using "Identify Mode" to Set the Device Address on the EXB ModulesThe ID Pushbutton on

Network Configuration14 ICSLan Device Control BoxesToggling Between Static and DHCP IP AddressingEXB modules support both Static IP and DHCP addresse

Network Configuration15 ICSLan Device Control Boxes Programming the EXB ModulesThe EXB Modules support specific NetLinx CHANNELS, LEVELS and SEND_COM

Network Configuration16 ICSLan Device Control Boxes

EXB-COM217 ICSLan Device Control Boxes EXB-COM2OverviewThe EXB-COM2 Networked COM2 Device (FG2100-22) provides 2 serial ports: one RS-232/422/485 por

EXB-COM218 ICSLan Device Control BoxesConnections and WiringLAN/PoE Port (RJ45)The LAN/PoE (RJ45) port on the rear panel provides 10/100 BaseT networ

EXB-COM219 ICSLan Device Control Boxes NetLinx ProgrammingEXB-COM2 Port Assignments EXB-COM2 SEND_COMMANDsThe following NetLinx SEND_COMMANDs are sup

EXB-COM220 ICSLan Device Control Boxes

EXB-I/O821 ICSLan Device Control Boxes EXB-I/O8OverviewThe EXB-I/O8 Networked 8-I/O Device (FG2100-21) provides eight Input/Output channels with LED

Table of Contentsi ICSLan Device Control Boxes Table of ContentsICSLan Device Control Boxes ...

EXB-I/O822 ICSLan Device Control BoxesConnections and WiringLAN/PoE Port (RJ45)The LAN/PoE (RJ45) port on the rear panel provides 10/100 BaseT networ

EXB-I/O823 ICSLan Device Control Boxes EXB-I/O8 SEND_COMMANDs The following NetLinx SEND_COMMANDs are supported by the EXB-I/O8 Module:Telnet command

EXB-I/O824 ICSLan Device Control Boxes

EXB-IRS425 ICSLan Device Control Boxes EXB-IRS4OverviewThe EXB-IRS4 (FG2100-23) Networked IR & I/O Device provides four IR/Serial and four I/O po

EXB-IRS426 ICSLan Device Control BoxesConnections and WiringLAN/PoE Port (RJ45)The LAN/PoE (RJ45) port on the rear panel provides 10/100 BaseT networ

EXB-IRS427 ICSLan Device Control Boxes Input LinkingThe EXB-IRS4 has 4 IR-Tx ports (labelled "IR/SERIAL") and 4 associated input pins. Each

EXB-IRS428 ICSLan Device Control BoxesLinked ModesThe following table describes the four linking modes on the EXB-IRS4: IO-Linked ModesUnlinked (defa

EXB-IRS429 ICSLan Device Control Boxes NetLinx ProgrammingEXB-IRS4 Port AssignmentsEXB-IRS4 Channel AssignmentsEXB-IRS4 Port AssignmentsPort Descript

EXB-IRS430 ICSLan Device Control BoxesEXB-IRS4 SEND_COMMANDs The following NetLinx SEND_COMMANDs are supported by the EXB-IRS4Module:Telnet commandsR

EXB-MP131 ICSLan Device Control Boxes EXB-MP1OverviewThe EXB-MP1Networked Television Control System Device (FG2100-26) provides one Serial (RS-232) p

ii ICSLan Device Control BoxesTable of ContentsPort 1(Multi-Protocol COM Port)...

EXB-MP132 ICSLan Device Control BoxesConnections and WiringLAN/PoE Port (RJ45)The LAN/PoE (RJ45) port on the front panel provides 10/100 BaseT networ

EXB-MP133 ICSLan Device Control Boxes When used for voltage inputs, the I/O port detects a low signal (0 - 1.5 VDC) as a Push, and a high signal (3

EXB-MP134 ICSLan Device Control BoxesNetLinx ProgrammingEXB-MP1 SEND_COMMANDs The following NetLinx SEND_COMMANDs are supported by the EXB-MP1 Module

EXB-REL835 ICSLan Device Control Boxes EXB-REL8OverviewThe EXB-REL8 Networked 8-Relay Device (FG2100-20) provides eight relays that support devices t

EXB-REL836 ICSLan Device Control BoxesConnections and WiringLAN/PoE Port (RJ45)The LAN/PoE (RJ45) port on the rear panel provides 10/100 BaseT networ

NetLinx Send Commands37ICSLan Device Control Boxes NetLinx Send CommandsThe following NetLinx SEND_COMMANDs are supported by the EXB-xxx modules. Net

NetLinx Send Commands38 ICSLan Device Control BoxesNetLinx Send Commands (Cont.)Command Description EXB ModulesCH Send IR pulses for the selected a c

NetLinx Send Commands39ICSLan Device Control Boxes NetLinx Send Commands (Cont.)Command Description EXB ModulesCP Halt and clear all active or buffer

NetLinx Send Commands40 ICSLan Device Control BoxesNetLinx Send Commands (Cont.)Command Description EXB ModulesCTSPSH Enable Pushes, Releases, and st

NetLinx Send Commands41ICSLan Device Control Boxes NetLinx Send Commands (Cont.)Command Description EXB ModulesGET INPUT Get the active state for the

Table of Contentsiii ICSLan Device Control Boxes Connections and Wiring...

NetLinx Send Commands42 ICSLan Device Control BoxesNetLinx Send Commands (Cont.)Command Description EXB ModulesIROFF Halt and Clear all active or buf

NetLinx Send Commands43ICSLan Device Control Boxes NetLinx Send Commands (Cont.)Command Description EXB ModulesPOF Turn OFF a device connected to an

NetLinx Send Commands44 ICSLan Device Control BoxesNetLinx Send Commands (Cont.)Command Description EXB ModulesPTOF Set the time duration between pow

NetLinx Send Commands45ICSLan Device Control Boxes NetLinx Send Commands (Cont.)Command Description EXB ModulesRXCLR Clear all characters in the rece

NetLinx Send Commands46 ICSLan Device Control BoxesNetLinx Send Commands (Cont.)Command Description EXB ModulesSET DBT Set Debounce Mode in 10ms incr

NetLinx Send Commands47ICSLan Device Control Boxes NetLinx Send Commands (Cont.)Command Description EXB ModulesSET MODE Sets an IR port to either IR,

NetLinx Send Commands48 ICSLan Device Control BoxesNetLinx Send Commands (Cont.)Command Description EXB ModulesSPGenerate a single IR pulse.• Use &ap

NetLinx Send Commands49ICSLan Device Control Boxes NetLinx Send Commands (Cont.)Command Description EXB ModulesXCH Transmit the selected channel IR c

NetLinx Send Commands50 ICSLan Device Control BoxesNetLinx Send Commands (Cont.)Command Description EXB ModulesXOFF Disable software handshaking (def

NetLinx Send Commands51ICSLan Device Control Boxes SEND_STRING Escape SequencesThe EXB-COM2 and EXB-MP1 support several special SEND_STRING escape se

iv ICSLan Device Control BoxesTable of ContentsIROFF...

NetLinx Send Commands52 ICSLan Device Control Boxes

Terminal (Telnet) Commands53ICSLan Device Control Boxes Terminal (Telnet) CommandsOverviewTelnet terminal communication can be accessed remotely via

Terminal (Telnet) Commands54 ICSLan Device Control BoxesIn this case, do not enter anything for the username when prompted. Simply press <Enter>

Terminal (Telnet) Commands55ICSLan Device Control Boxes Terminal Commands (Cont.)Command DescriptionEXIT Exit the telnet sessionFACTORYFWIMAGE Reset

Terminal (Telnet) Commands56 ICSLan Device Control BoxesTerminal Commands (Cont.)Command DescriptionGET IP Displays the IP configuration of a device.

Terminal (Telnet) Commands57ICSLan Device Control Boxes Terminal Commands (Cont.)Command DescriptionSET CONNECTION Set the master connection settings

Terminal (Telnet) Commands58 ICSLan Device Control BoxesTerminal Commands (Cont.)Command DescriptionSET ETHERNET MODE This command sets the current L

Terminal (Telnet) Commands59ICSLan Device Control Boxes Notes on Specific Telnet ClientsTelnet and terminal clients will have different behaviors in

Terminal (Telnet) Commands60 ICSLan Device Control BoxesLinux Telnet ClientThe Linux Telnet client has three anomalies that are known at this time:

Terminal (Telnet) Commands61 ICSLan Device Control Boxes

Table of Contentsv ICSLan Device Control Boxes GET CONNECTION ...

8/12 ©2012 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX. AMX reserves the right to alter specifications without no

vi ICSLan Device Control BoxesTable of Contents

ICSLan Device Control Boxes1 ICSLan Device Control Boxes ICSLan Device Control BoxesOverviewThe EXB family of ICSLan Device Control Boxes (FIG. 1) pr